PurePower+™ 1500 Black AC Regenerator
pcX USD Price: $3,250.00
Model 1500 (120V) - 1500VA / 1350 Watt Capacity AC Regenerator
Now In Stock:
For More Information or To Order:
Call 1-866-681-9602 or
E-Mail Chris at firstname.lastname@example.org
The Technology Behind the PurePower™ APS
Your AC power supply would be ideal if you could plug your system components directly into the main generator at the nearest hydro electric generating station without the intervening transmission system and other customers sharing the line – assuming you could hear the music over the roar of the waterfalls. The PurePower™ APS provides the next best thing. It quietly generates a new, clean, 120 volt 60 cycle sine wave right beside your audio or home theatre system, so there is no opportunity for outside influences to introduce unwanted waveform distortions.
Our Double Conversion Design:
The utility supply from the wall outlet is filtered and surge protected. It is then converted by a rectifier circuit to a finely regulated direct current. This DC is then used by the inverter circuit to regenerate a new clean AC source. The battery module placed on the DC side ensures that no matter what happens to the utility power supply, there will be full current and voltage at the rated value to keep your components connected to an ideal pure power supply.
This double conversion technology provides a perfect barrier to power problems that might exist in the utility line. No distortions can pass through the DC intermediate circuit. No EMI, no RFI, no spikes, no high voltage transients, no damaging surges can reach your components. In fact, if it were possible for a damaging spike to get past the PurePower™’s built in surge protection system, it would still not reach your sensitive components.
The PurePower™ APS maintains the accuracy of its 120 volt sine wave at a steady 60 cycles even at its full output no matter how low or high the voltage of the utility supply, so the amplifier never suffers current limits, regardless of how momentary.
Utility Supply vs. Regeneration:
Does regenerated power really give me anything that the power in my wall can't provide?
Recent testing conducted voltage and a host of harmonic distortion at various frequencies resulting in flat topped wave forms, but reasonably good as utility supplies go. The power output of the PurePower™ APS was measured showing full availability with minimal harmonics or wave form distortion.
The power requirements of a Bryston 9B SST THX 5 channel power amplifier was measured with broad spectrum pink noise input. Measurements were take both on utility and with the addition of the APS. There were dramatic differences in current draw between the two setups. Without the PurePower™ APS, the amplifier could not draw the current it was asking for. The addition of the APS increased the power draw of the Bryston by almost 2 amps. The measurements also showed marked reduction in total voltage distortion and the ability to match the needs of the equipment. This is achieved without the overwhelming overhead of some other regeneration technologies - the PurePower™ APS has an energy efficiency of between 85 and 92%!
The PurePower AC regeneration design provides something you might not expect from a power solution. Many power filtering and conditioning products are routinely accused of limiting the current flowing though them, thus starving the power amps with their need for lots of instantaneous current on demand. Testing shows how the PurePower actually has the capability to deliver more current that even a completely unfettered and unfiltered household outlet. In the Bryston equipment test measurements shown above, the 9B SST demanded AC to produce the required output to the speakers. The Amp drew 3.88 amps at its peak demand. When powered from the PurePower 1050, the amp was able to draw 5.6 amps at peak! That's almost a 50% increase! This is possible due to the nature of our AC regeneration technology. One of our primary goals is to be able to provide for maximum current variation on demand without allowing the sine wave or voltage level to be adversely affected. While you want voltage to be rock solid, noise to be at a minimum and the sine wave to be pristine, you also want to be able to have the most current possible available exactly when it is needed. The more instant current change you can provide without affecting any of the other power variables, the better your system can perform.
|Nominal Voltage||120 VAC|
|Voltage Range||55 - 150 VAC|
|Frequency||50 / 60 Hz Auto-sensing|
|Frequency range||40 - 70Hz|
|Input Connection - All models||IEC 320-C19 Input receptacle|
|Output Voltage||120 VAC (110/115/120/127 VAC - User selectable)|
|Voltage Regulation||± 1% of nominal|
|Output Frequency||50 or 60 Hz - user selectable|
|Frequency Regulation||± 0.5%|
|Efficiency||88 - 92% depending on load|
|Output receptacles - PP+ 1500||(10)Hubbell NEMA 5-15R|
|Output receptacles - PP+ 2000/3000||(10) Hubbell NEMA 5-15R + (2) Hubbell L5-20R|
|Optional receptacles||Furutech High Performance Receptacle Option|
|Standby power consumption||10 watts|
|Output Power - PP+ 1500||1350 watts continuous / 1750 short term (2 min.) / 2700 (10 sec.) / 6750 (inst.)|
|Output Power - PP+ 2000||1800 watts continuous / 2340 short term (2 min.) / 3600 (10 sec.) / 9000 (inst.)|
|Output Power - PP+ 3000||2700 watts continuous / 3510 short term (2 min.) / 5400 (10 sec.) / 13,500 (inst.)|
|EMC monitors||FCC Class B and VCCI Class II|
|Surge Supression||IEEE / ANSI C62.41 Category B (formerly 587)|
|Ambient Operating Temp.||32 - 90• F (0 - 32•C)|
|Audible noise||<17 dBA|
|Relative humidity||0 to 90% non-condensing|
|F-Type (coax) surge protection||2 input, 2 output|
|Phone line surge protection||1 line input RJ11|
|RJ45 Transient protector||Input and output jack for RJ-45 cable protection, UL497A tested|
|User selectable bypass||Bypass mode may be selected at any time. Automatic bypass on sustained overload|
|Diagnostics||Full system self-test on power up, user selectable diagnostics at any time|
PurePower™ Audio Power Supplies
PurePower™ models 1500, 2000 and 3000 are available with optional rack mount hardware to suit any installation requirement. All models have RJ11, RJ45, cable, and satellite coax surge protection modules. Model 1500, 2000, 3000 and their Power packs can be mounted vertically.